Leave your details and our team will get in touch.
Request a call back
Waterproof Render in Richmond
Keep damp, rain and cold from taking their toll on your walls.
Render does more than give a wall its finish: it adds a protective layer against cold and moisture entering the masonry. No render is 100% waterproof on its own, but a correctly chosen and applied waterproof render protects most of the underlying wall from frost damage, cracks, mould and damp patches. With waterproofing slurry beneath it, the layers create a complete barrier against water.
For interior and exterior walls in Richmond TW9, the CSSW-qualified team at Crystal Damp Proofing & Basements Ltd selects a system to suit the building and applies waterproof render in Richmond.
How do we make render waterproof?
Specialist additives go into the render mix. As they enter and bond within the material’s pores, they create an internal protective coating that greatly limits water absorption. We choose between these renders according to the wall’s location and conditions:
- Cement renders with waterproofing additives: our strongest, most watertight option for particularly exposed areas and interior basement walls.
- Silicone renders: strongly repel water, allowing rain to wash dirt away as it runs off.
- Acrylic renders: offer flexibility and weather resistance while absorbing little water.
- Mosaic (resin) renders: withstand water and impact particularly well; they are most often used on plinths.
- Renovation renders: resist salts while remaining highly breathable for the restoration of old, damp walls.
What does waterproof render protect your walls against?
A suitable waterproof render helps protect your property from:
- Driving rain and splashback: rainfall striking walls directly or rebounding from the ground.
- Rising and penetrating damp: water entering masonry from below (rising damp) or passing through the wall (penetrating damp).
- Frost damage: moisture held in a wall expands as it freezes, causing cracks in both masonry and render.
- Cold and heat loss: walls provide much better insulation when dry than when wet.
- Mould, algae and moss: growth that takes hold on persistently damp surfaces indoors or outside.
Walls we can render
When and where is waterproof render useful?
Whether indoors or outside, waterproof render is particularly useful where walls face greater exposure to water.
Exterior walls and exposed areas
- Plinths and lower walls: the bottom 30–50 cm of the façade, where rainfall splashes back and snow can lie.
- Foundation and basement areas: ground-contact walls without full vertical waterproofing, or walls needing added protection. Read about retaining wall and foundation waterproofing.
- Exposed walls: elevations facing prevailing wind and rain, as well as slow-drying surfaces where algae grows.
- Around terraces, balconies and entrances: render reached by water running or splashing off flat surfaces.
- Near water and trees: properties close to rivers, lakes or woodland, where the air remains humid.
Interior spaces and older masonry
- Old, damp walls: during the restoration of buildings affected by moisture.
- Interior walls: in basements, cellars and other rooms vulnerable to damp.
Must the mortar be repaired before render is applied?
Yes. A render system needs sound masonry beneath it. We rake out loose or crumbling mortar and repoint to a depth of at least 20 mm; cracks must be repaired before rendering too. This preparation provides a stable base and is essential to effective waterproofing.
Tanking basement walls before rendering
Basement and cellar walls receive spray-applied tanking before we render them. This polymer-modified, mineral cement waterproofing mortar is machine-applied in at least two coats, around 2–3 mm thick altogether. It bonds permanently to the wall, creating a continuous watertight barrier against ground moisture and water pressure.
Applying the slurry by spray rather than by hand brings several advantages:
- No weak spots: slurry reaches into pores, hollows and uneven parts of brick, stone and concrete that a brush or trowel may leave thin or miss.
- One seamless coat: water has no joints or overlapping edges to follow.
- Even coverage and speed: corners and spaces behind services receive a consistent layer across the wall, much faster than hand application.
Slurry + render
Why combine spray-applied tanking with waterproof render?
Slurry and render have separate roles; used together, they provide stronger protection than either layer alone.
A smooth, ready-to-finish wall: render evens out the surface and creates a sound base for paint or another finish, helping the basement look like the rest of the home.
How the layers are built up
Applying waterproof render over tanking slurry
For cellar and basement walls, we normally build up a layered system. Beneath the render, tanking slurry blocks water; the render protects that barrier, evens out the wall and supports the final finish.

Important rules and mistakes to avoid
- The right order: for waterproofing a basement internally, slurry must sit beneath the render, on the side from which water arrives.
- Corners and junctions: we set sealing tape into the slurry where walls meet one another or the floor, because building movement can cause cracks there.
- Curing: during the first few days, we mist both layers lightly and shelter them from drying too quickly in sunshine or draughts.
- Too thin a layer: slurry under 2 mm thick cannot provide full waterproofing.
- The wrong conditions: we render only between +5°C and +25°C, without rain or strong wind, and never onto a wall that is soaking wet.
Assess the moisture first
Is the wall damp, or is water pushing through?
What the water is doing in the room determines which waterproofing system is appropriate.
Rising damp and damp masonry
Ground moisture travels upwards through the masonry. Salts may appear and the walls feel damp, although water is not running in.
Water standing against or pressing through a wall
When water sits against the outside of a wall, it pushes towards the room. This negative pressure tries to detach the waterproofing. Ordinary waterproof render and standard flexible slurry cannot resist it: water can lift them from the masonry and leave blisters.

Our approach when water pushes in
- Stopping active leaks first: we open up seeping or spurting points into a dovetail shape, then plug them with hydraulic cement that sets in seconds on contact with water.
- Back to sound masonry: we remove old render at least 80 cm above the visible damp line, ideally to ceiling height in basements, and wire-brush away salt deposits.
- Fillets at the wall-to-floor junction: repair mortar forms a rounded fillet with a radius of around 4–5 cm where pressure from water is highest.
- Rigid mineral slurry: we use slurry designed to resist negative pressure, often using crystalline technology, in at least 2–3 coats to a cured thickness of at least 3 mm.
- Render on top: a suitable bonding coat precedes render chosen for the conditions.
If water presses in constantly at high pressure, slurry and render alone may not keep a habitable room dry. In line with BS 8102, we recommend a cavity drain membrane system (Type C), drainage and a sump pump instead. Find out more on our basement waterproofing page.
Walls affected by salts
Renovation render for rising damp and salts
Ordinary waterproof render can fail on a wall affected by rising damp and salts: trapped moisture remains in the masonry, while salts build up and force the render away.
How a renovation render system is built
- Bonding coat: first comes a semi-covering renovation spatterdash coat.
- Renovation render: we then apply porous, air-entrained renovation render at least 20 mm thick.
How it works: countless small pores let remaining moisture escape as the wall breathes. Harmful salts crystallise within those pores, rather than breaking up the surface.
Dealing with rising damp within the wall
When moisture rises from the foundations, internal slurry stops it reaching the room but cannot dry the inside of the masonry. The room may be dry while the wall remains wet within.
To stop the rising moisture at its source, we recommend DPC injection. We drill into the wall and inject a specialist cream or silane-based fluid to create a water barrier inside the masonry.

If there is no sump chamber
Need a sump chamber? We can help fit one
Standing water on a room’s floor needs a way out before waterproofing begins. If there is no sump chamber, we can help you install one.
- Sump chamber at the lowest point: the chamber sits within the floor and houses an automatic sump pump to carry water outside the building.
- The right discharge point: water can enter a foul or combined sewer through a trapped gulley that prevents smells returning, or a surface water drain through a non-return valve.
- Back-up protection: a battery back-up (UPS) or generator powers the pump during an outage; in a twin-pump arrangement, the other pump starts if one fails.
- Regular servicing: we advise servicing twice a year to clean the chamber, inspect the float switch and test whether the pump starts automatically.

The materials we use
Established manufacturers and quality materials
Products from established manufacturers, including Newton, Wykamol, Delta, Biokil and Mapei, work together as a complete system to protect your walls for years to come.
NEWTON
Newton
Membrane systems and waterproofing slurries.

Wykamol
Renovation products, additives and tanking slurries.

Delta
Sump pumps, drainage channels and membranes.

Biokil
Treatments for mould and damp proofing.
Mapei
Repair products, waterproof renders and mortars.
Other services for your walls
Waterproof render alongside our other services
A rendering system may be combined with other work, including spray-applied tanking or comprehensive basement waterproofing.
Spray-Applied Basement Waterproofing
A slurry barrier beneath the render.
Basement Waterproofing
Pumps, membranes and tanking systems.
Cellar Waterproofing
Dry protection for older cellars.
Rising Damp
Addressing moisture rising through masonry.
Penetrating Damp
Dealing with water entering through walls.
Crystalline DPC Injections
Forming a damp proof course within walls.
Structural Cracks Repair
Preparing cracked walls for rendering.
Retaining Wall & Foundation Waterproofing
Waterproofing walls that retain soil.
Sump Pump System & Services
Removing water by pump.
ISO-Therm Membrane & Black Mould
Solutions for condensation and mould.
Basement Waterproofing Technology
A guide to Type A, B and C.
Insurance-Backed Guarantee & Product Warranty
Cover that passes to a buyer on sale.
Common questions
Questions about waterproof render
Is waterproof render completely waterproof?
On its own, no render is 100% waterproof. Additives significantly limit absorption, protecting most of the masonry underneath. When applied over tanking slurry, the combined layers create a complete water barrier.
Which type of waterproof render do I need?
The wall’s position and exposure guide the choice. Cement render with waterproofing additives suits highly exposed areas and basement walls; silicone sheds rain and resists algae; acrylic is flexible and weather-resistant; mosaic protects plinths; and renovation render suits older walls affected by salts. We advise on the system after surveying the wall.
Do you repair the mortar before rendering?
Yes. Render needs a sound wall behind it. We rake out and repoint loose or crumbling mortar to at least 20 mm deep and repair cracks before applying render.
How thick are the slurry and render layers?
We apply tanking slurry in at least two coats to at least 2–3 mm overall. Above it, waterproof render is at least 10–15 mm thick; renovation render is at least 20 mm thick.
Can you render a basement wall where water is pressing in?
Yes, provided the system matches the conditions. We plug active leaks with fast-setting hydraulic cement, then use rigid mineral slurry designed for negative pressure, at least 3 mm thick, before rendering. For constant, high-pressure water, we recommend a cavity drain membrane system (Type C) in line with BS 8102.
Why use renovation render on walls with rising damp?
Its porous, air-entrained structure allows the wall to breathe and gives salts space to crystallise inside the pores rather than damage the surface. A breathable mineral paint or coating completes the finish. We recommend DPC injection to stop rising damp at its source.
When can render be applied?
We render only between +5°C and +25°C, when there is no rain or strong wind, and never onto a soaking wet wall. During the first few days, we lightly mist the slurry and render to prevent them drying too rapidly.
How do I book a survey in Richmond?
For a survey in Richmond, book online or speak to our specialists on 020 8432 3350 or 07720 752231. We will assess your walls and advise on a suitable interior or exterior render system.
Your free survey
Arrange a wall survey in Richmond
Whether your walls are damp or cracked, the render is blown or water is entering your basement, book a survey or speak with our specialists on 020 8432 3350 or 07720 752231.
07720 752231
Tell us what is happening to your walls
Please fill in the fields marked *. We will get in touch to arrange your survey once we receive your details.
Considering the local property
What we assess before rendering in Richmond
In Richmond, walls in older terraces and newer properties can call for different approaches. We inspect the actual masonry and its condition before selecting render, rather than assuming every building needs the same system.
Our on-site checks cover the wall’s orientation and rain exposure, mortar and cracks, evidence of salts or rising damp, and any water pressing in from the ground. These findings shape the preparation and render choice, including whether tanking slurry should go underneath.
Responsible for the render we apply
Every render we apply is our responsibility. Should a defect arise in our work, we put it right.
Our own qualified team completes each project, making it clear who carried out the work and who is accountable. We also undertake waterproof render in Twickenham, Kingston upon Thames and Hounslow.

Work completed by our team

Concerned about damp, cracks or blown render?
We are proud to have a 5-star Google rating. Arrange a survey, explore our reviews or speak to our specialists on 020 8432 3350.
Qualified Specialists & a 10-Year Guarantee
Our family-run team holds CSSW qualifications, with a minimum of 10 years’ experience each. We back every job in Richmond with a 10-year guarantee covering workmanship, plus a QANW Insurance Backed Guarantee that transfers to the new owner if you sell your property. We work on domestic and commercial properties in Richmond and across London and the South East.
See What Our Clients Say
★★★★★ Rated 5 stars on Google
We are proud of our 5-star Google rating: see our reviews. If your basement or property in Richmond is damp or takes in water, book a survey in our Booking Survey section, or call or message our fully qualified advisors.
Our service area
Waterproof rendering around Richmond
For walls inside and out, Crystal Damp Proofing & Basements Ltd provides waterproof render in Richmond and surrounding areas, including Twickenham, Kingston upon Thames and Hounslow. Select an area below for its local page.






