Leave your details and our team will get in touch.
Request a call back
Basement Floor & XPS Insulation for Richmond Homes
Make your basement floor and walls warmer and drier for everyday living.
A bare concrete slab can leave a basement cold throughout the year, draw warmth from the room and encourage condensation and mould. Proper basement floor insulation helps make the space feel warm, dry and solid underfoot.
For homes in Richmond TW9, Crystal Damp Proofing & Basements Ltd insulates basement floors and walls with extruded polystyrene (XPS) within a complete waterproofing system. We work on basement living rooms, bedrooms, home offices, gyms, cellars and other below-ground spaces.
Where basement insulation is used
For below-ground rooms intended for everyday comfort, we use XPS to insulate floors and walls in:
- new basements and basement conversions
- older cellars converted into bedrooms, living rooms or home offices
- playrooms, cinema rooms and basement gyms
- flats on the lower ground floor
- vaults and other below-ground spaces intended for daily use
Choosing the insulation material
Understanding XPS insulation
The closed-cell structure of extruded polystyrene (XPS) makes this rigid insulation board suited to demanding parts of a building, including basements.
Why not standard expanded polystyrene (EPS)? In wet ground, ordinary EPS absorbs water and loses insulating performance. For below-ground use, particularly with a high water table, XPS is the appropriate choice.
The benefits of insulating a basement floor
An uninsulated slab can keep a basement feeling separate from the rest of your home. Floor insulation helps in several ways:
- Comfort: however much you heat the room, an exposed cold slab can leave it feeling chilly.
- Less condensation and mould: moisture is less likely to condense on a warmer floor surface.
- Lower heating bills: insulating the floor reduces heat loss into the ground.
- Building Regulations: a basement floor converted for living space must satisfy the thermal requirements of Part L.
- Underfloor heating: with insulation beneath the screed, heat travels into the room rather than down into the ground.
External or internal insulation
Comparing XPS outside and inside the basement
Whether installed beneath the floor or on either side of a basement wall, XPS serves a different purpose in each position. On a phone, the comparison columns display as separate cards.
Outside the basement
Retaining walls and foundations
- Moisture resistance: essential where groundwater is present. XPS retains its insulating performance in wet ground without absorbing that water.
- Mechanical strength: very high, helping it withstand frost heave and soil pressure while shielding the waterproofing from damage.
- Thermal insulation: prevents walls from freezing and removes cold bridges at the point where the building meets the ground.
- Biostability: complete resistance to insects, bacteria, fungi and rot in the surrounding soil.
Inside the basement
Internal walls and floors on the ground
- Moisture resistance: supports the system by resisting ground moisture, although proper waterproofing is still required.
- Mechanical strength: high for floors, supporting the layers above and heavy loads from everyday use.
- Thermal insulation: separates floors from the cold ground; insulating walls internally calls for careful design.
- Biostability: resistance to fungi and mould is valuable in basements with poor ventilation.

External insulation: our recommended approach
On the outside of a basement wall, XPS provides insulation and shields delicate waterproofing, including bituminous coatings on retaining walls. It protects those coatings against sharp stones during backfilling and against plant and tree roots.
- Fully bonded: rather than fixing boards in dabs, we bond their entire surface to the waterproofing. This prevents water circulating behind them between the wall and the XPS.
- Rebated edges: shiplap-edged boards close the gaps through which water could otherwise wash across the insulation.
- Heavy-duty waterproofing first: with a high water table, a robust layer such as a reinforced bituminous coating or membrane is applied directly to the wall before the XPS. Of the insulation options, XPS alone can remain in groundwater permanently without losing insulating value.
Choosing an approach for your property
Insulating new and existing basements
Our insulation approach starts with whether we are working on a basement under construction or one that is already there.
Newly built homes
For new homes we build with a basement, XPS is standard; we can install it mainly from outside while the structure is accessible:
- Foundation walls: with ample space outside, we bond boards directly to the smooth new waterproofing, using the thickness required by Part L.
- Protection during backfilling: as heavy machinery fills the excavation, the XPS protects the newly applied waterproofing.
- Floors: beneath the slab or screed, we install smooth or rebated boards. Compressive strength of, for example, 300 or 500 kPa supports boilers, water tanks and heat pumps without the floor settling.
Existing properties and older buildings
Limited access, damp and uneven old masonry shape the work in an existing basement:
- Outside, by excavation: this is the most effective approach for drying an older basement and separating it from cold ground. We protect existing foundations, level uneven stone and brick with a render, then apply new vertical waterproofing before bonding the XPS.
- Inside, without excavation: an option when external digging cannot be done, such as where a neighbouring building is too close or permission has been refused.
- Floors in old basements: removing an old damp floor and lowering the basement is often necessary to fit the waterproofing and XPS without sacrificing limited headroom. We coordinate this with the basement conversion.
Why choose XPS over standard PIR beneath a cavity drain membrane?
A cavity drain membrane in a Type C system (BS 8102:2022) manages water entering through the structure. Moisture, including standing water, may therefore remain in the layers below the membrane, where insulation must tolerate it:
- Moisture resistance: XPS takes up almost no water, does not rot and retains its insulating value through prolonged wet conditions. Although foil-faced PIR boards perform excellently when dry, persistent damp can cause their facings to delaminate and their cores to absorb moisture.
- Compressive strength: floor-grade XPS boards typically carry ratings of 300 kPa or higher, supporting furniture, partition walls and screed without settling. We check long-term creep as well as short-term strength because these loads remain for decades.
- Drainage: grooves beneath some XPS floor boards allow water to travel freely towards the perimeter drainage channels.
XPS insulates; waterproofing keeps the water out. Despite its moisture tolerance, water can move between XPS boards. Under BS 8102:2022, it is not one of the three recognised protection types. We therefore fit it within a complete system comprising the cavity drain membrane, perimeter drainage channels and a sump with an automatic pump to discharge water outside.
Building a Type C floor
Our insulated basement floor build-up
Our usual insulated basement floor build-up follows these steps:
- Survey: we assess the slab, water level, available headroom and preferred finish before selecting a suitable board thickness.
- Preparing the slab: after cleaning and levelling the floor, we repair cracks and create perimeter drainage channels linked to the sump.
- XPS insulation: boards are laid tightly together directly on the concrete slab across the whole floor. Edge insulation beside the walls prevents cold bridges.
- Cavity drain membrane: we install the floor membrane, seal its joints and link it to both the wall membranes and drainage system.
- Screed and finish: the screed goes down, incorporating underfloor heating if wanted, ready to receive your chosen floor finish.



Insulation where the water table is high
Floor insulation with a high water table
Where the water table is high, groundwater presses continuously on basement floors and walls and can push upwards beneath the floor. This makes insulation particularly challenging. Because joints between XPS boards are not watertight, the layers around them matter. Depending on the building, we use a Type C system or construct a sealed, tanked floor in stages:

Important: the finished floor needs enough weight to resist upward water pressure. A structural engineer always specifies the loading slab’s exact reinforcement and thickness; we do not guess. If a flexible mineral tanking slurry is installed beneath the XPS, we apply it as a single seamless layer.
Internal insulation for basement walls
Where an existing basement wall cannot be reached from outside, internal insulation may be needed. The design requires particular care:
- Stop the water first: groundwater passing through a wall must not be trapped behind internal XPS: moisture could build up, damage masonry and cause mould, even though the board itself does not rot. We address water first with a crystalline DPC injection forming a barrier within the wall, a mineral tanking slurry resistant to negative pressure, or a cavity drain membrane system.
- The dew point: internal insulation shifts it into the wall, where uncontrolled water vapour can condense behind the XPS and damage masonry. We assess this carefully, use thermal imaging when needed and include vapour control where required.
- Rough-faced boards: when walls will receive adhesive and plaster, rough or waffled XPS boards provide much better adhesion.
The materials we use
Proven products and quality materials
Our waterproofing suppliers provide high-quality XPS boards, which we combine with proven products from recognised manufacturers including Newton, Wykamol, Delta, Biokil and Mapei. Used together as a complete system, these materials keep a basement warm and dry for years to come.
NEWTON
Newton
Pump systems and cavity drain membranes.

Wykamol
Sump pumps, membranes and tanking slurries.

Delta
Pumps, channels and studded membranes.

Biokil
Treatments for mould and damp proofing.
Mapei
Waterproof coatings alongside repair mortars.
Complementary basement services
Services to support your basement floor insulation
A comfortable, usable basement needs more than floor insulation alone. Our related work includes basement waterproofing, basement conversions and sump pump installation.
Waterproofing for Basements
Tanking, membranes and pumps.
Basement Conversion and Waterproofing
Turning a damp cellar into living space.
Retaining Wall & Foundation Waterproofing
Protection outside before backfilling.
Sump Pump System & Services
Pump installation and servicing.
Spray-Applied Waterproofing for Basements
Sprayed tanking slurry.
Cellar Waterproofing
Keeping older cellars dry.
Crystalline DPC Injections
A damp proof course within walls.
Thermal Inspection
Finding concealed damp and cold bridges.
Common questions
Basement floor insulation questions answered
Why choose XPS instead of EPS or PIR for a basement?
Insulation below ground may remain damp for decades. XPS takes up almost no water and retains its insulating value when wet. Ordinary EPS absorbs water from wet ground, while foil-faced PIR, although excellent in dry areas, can delaminate and lose performance in persistent damp beneath a cavity drain membrane.
Will XPS waterproof my basement?
No. Although XPS tolerates moisture, water can travel through joints between boards. BS 8102:2022 does not recognise it as a waterproofing protection type. We fit it within a complete system, either with a cavity drain membrane, drainage and sump pump, or as part of a sealed, tanked floor.
What thickness of basement floor insulation do I need?
That depends on the U-value required by Part L, available headroom, screed type and whether underfloor heating is planned. At the survey, we specify a build-up that satisfies Building Regulations while using no more height than necessary.
Does floor insulation take away ceiling height?
Together, the membrane, insulation and screed lift the finished floor. For a cellar with limited headroom, we coordinate the build-up with the conversion and lower the floor where needed to keep the space suitable for living.
Is underfloor heating possible in a basement?
Yes. We place XPS beneath the screed, with heating pipes or mats above the insulation. This directs heat up into the room rather than allowing it to escape into the ground.
How is insulation handled with a high water table?
We can manage water using our Type C membrane, drainage and pump system. Alternatively, a sealed, tanked floor includes waterproofing beneath the XPS, boards rated at least 300 kPa, a separating layer and a reinforced loading slab sized by a structural engineer.
Why are XPS boards kept covered during the work?
Sunlight affects both XPS boards and membranes. Although they are completely dark once the floor is finished, boards left in sunshine for weeks beforehand may yellow and become brittle at the surface. We cover stored materials and install the membrane and screed over the insulation without unnecessary delay.
How can I arrange a basement survey in Richmond?
Arrange a survey online, or speak to our specialists on 020 8432 3350 or 07720 752231. We assess the slab, water conditions and headroom before advising on a suitable floor build-up.
Free basement survey
Arrange your basement survey in Richmond
For a basement floor that feels cold or damp, arrange a survey or speak with our specialists on 020 8432 3350 or 07720 752231. We assess the slab and water conditions, then advise on suitable waterproofing and insulation.
07720 752231
Describe your basement
Please complete the fields marked *. We will get in touch after receiving your details to arrange the survey.
Local basement considerations
What we assess in Richmond basements
In Richmond, a proposed basement floor may be in an existing cellar or a newly built space. Rather than assume what a property needs from its location, we assess the basement before recommending its floor build-up.
During the visit, we look at the slab and walls, available headroom and intended use, as well as whether water appears only after rain or remains present. This guides the choice between a Type C floor and a sealed, tanked floor, plus the board thickness and strength.
Allow for the finished floor level early
Adding a membrane, insulation and screed raises the floor. In a low-ceilinged cellar in Richmond, the remaining headroom may determine whether a living space meets Building Regulations.
- Plan it with the conversion: for a bedroom, gym or office, coordinate the floor build-up and any necessary lowering with the conversion before work is complete, rather than finding a headroom problem afterwards.
- How thick should the insulation be? The U-value specified by Part L, available ceiling height, screed choice and any underfloor heating all affect the answer. We establish the build-up at the survey to satisfy Building Regulations without unnecessarily reducing headroom.
- One team, one plan: we work with our architects and engineers to coordinate insulation, waterproofing and conversion within the same project.
- Nearby areas: basement floor insulation is also available from us in Twickenham, Kingston upon Thames and Hounslow.

Getting started

Let us make your basement warm and dry underfoot
Our 5-star Google rating makes us proud. You can arrange a survey, look through our reviews or speak to our specialists on 020 8432 3350.
Qualified Specialists & a 10-Year Guarantee
Our family-run team holds CSSW qualifications, with a minimum of 10 years’ experience each. We back our work in Richmond with a 10-year guarantee covering workmanship, plus a QANW Insurance Backed Guarantee that transfers to the new owner if you sell your property. The waterproofing materials also carry a 10-year product warranty. Based in Croydon, we work on domestic and commercial properties across London and the South East.
See What Our Clients Say
We are proud of our 5-star Google rating. If you want a warm, dry basement floor, book a survey or call our specialists on 020 8432 3350 or 07720 752231.
Where we work
Basement floor insulation across Richmond and surrounding areas
For basement floor insulation in Richmond and nearby areas such as Twickenham, Kingston upon Thames and Hounslow, you can contact Crystal Damp Proofing & Basements Ltd. Select an area below to view its local page.








