Leave your details and our team will get in touch.
Request a call back
Penetrating Damp in Richmond
Trace the water, stop the leak and restore your walls.
Penetrating damp occurs when water enters a building from outside or through a damaged service pipe, then passes through walls, floors, roofs or ceilings. Unlike rising damp, which moves upwards from the ground, it can show up anywhere from the basement to the top floor, though it is most common below ground.
For homes in Richmond TW9, Crystal Damp Proofing & Basements Ltd identifies where the water is entering, stops it at the source and restores the affected walls.
The main causes
For water to enter, there must be an opening. The routes we encounter most often are:
- Damaged roofs and gutters: leaking roof coverings, cracked or displaced tiles, and blocked or broken gutters and downpipes can direct water down the facade.
- Defects in the facade and walls: cracked or porous brickwork, damaged render, deteriorating mortar joints or absent waterproofing provide a route in.
- Leaking services: damaged drains and leaking water or waste pipes within walls or ceilings can also leave the structure wet.
Surveying penetrating damp
Our detailed surveys establish where penetrating damp starts and how far it has spread through your property. Experienced surveyors use specialist equipment, including thermal imaging cameras, to locate moisture that may not be visible, so the cause can be addressed before it leads to structural damage or health risks from mould and fungi.
Does a wet patch always indicate penetrating damp?
Not necessarily, although it is a likely cause. Where the patch appears and how it changes offer useful clues:
- Penetrating damp: a patch may appear or spread after heavy rain, particularly near windows, beneath ceilings or in corners.
- Condensation: moisture and mould develop at cold spots, including thermal bridges, room corners and areas behind furniture. Poor ventilation and high indoor humidity, rather than rainfall, are the cause.
- Plumbing leaks: a persistently wet, expanding patch near a water or waste pipe, regardless of the weather, generally suggests a pipe leak.
How to spot penetrating damp
Once penetrating damp becomes established, it often leaves visible clues. Watch for:
- Wet patches and stains: areas of moisture or discolouration on a wall or ceiling that develop or spread after heavy rain.
- Damaged finishes: wallpaper lifting away, paint flaking or plaster blowing.
- Mould and fungus: growth in room corners or across the wall surface.
- A musty smell: a lingering damp odour even after you have aired the room.
Where does it develop, and when?
Areas around structural cracks and places vulnerable to leaks or escaping water are common trouble spots. Water can also migrate into walls when a damp-proof course (DPC) fails. In many older London homes, a failing DPC can contribute to hygroscopic salt build-up and rising damp.
Basements and penetrating damp
Much of the penetrating damp we tackle affects basements, cellars and vaults. Wet soil remains in contact with basement walls, pressing water against them throughout the year. Below ground is where this problem is most common and can cause the greatest damage.
What lets water into a basement?
- Flooding: heavy rain, a high water table or inadequate drainage can put pressure on basement walls and floors. Without waterproofing, water can soon enter.
- Structural cracks: most buildings over 50 years old, particularly Victorian houses, were constructed without basement waterproofing. Cracks developing over time give water a direct route inside.
- Movement and vibration: settling buildings, moving ground or vibration from traffic on a busy road can widen existing cracks and create new ones.
- Joints and weak points: entry points also include construction joints, pipe penetrations and the junction between basement walls and floors.
BS 8102:2022
Choosing between Type A and Type C waterproofing
BS 8102:2022 describes three approaches to basement waterproofing: Type A, a barrier system also called tanking; Type B, structurally integral protection using reinforced waterproof concrete only in new buildings; and Type C, which combines a cavity drain membrane, drainage and a sump pump. Type A and Type C can both suit many basements. If walls move or vibration from a nearby road affects the building, however, Type C is the system to use.
Type A: a bonded barrier
Tanking bonds directly to the wall to form a barrier against water.
- Where it works: walls that are sound and stable, with few cracks, where an unbroken barrier can resist water.
- The risk: ongoing wall movement may crack the bonded tanking and allow water through.
Type C: a cavity drain membrane
The membrane is independent of the wall, with drainage behind it.
- Where it works: basements affected by multiple structural cracks, movement or vibration from a nearby road.
- Why it stays dry: water entering through a new crack travels behind the membrane to drainage channels, then is pumped away.

Concrete and new buildings
Concrete basement walls and dry-pack joints
Concrete basement walls are not immune to cracking. Forming or deepening a basement through underpinning involves casting new concrete in sections. A stiff mortar called dry-pack fills the space between each section and the existing wall above. As concrete shrinks and the building settles, these joints can crack and admit water.
Type B waterproof concrete is reserved for new buildings with reinforced concrete structures, yet its joints can still crack. In most new buildings using Type B, we therefore add a Type C cavity drain membrane over the waterproof concrete. BS 8102 recommends this combined protection for habitable basements: if a crack forms, water can be collected and pumped away rather than flood the space. Explore our basement conversion and underpinning work.



Waterproofing below ground
Our services for basement waterproofing
With so much penetrating damp occurring below ground, we provide a full range of basement waterproofing services. Each waterproofing installation comes with our 10-year guarantee and a QANW Insurance Backed Guarantee.
Basement Waterproofing
Type A and Type C waterproofing in line with BS 8102:2022.
Basement Conversion & Waterproofing
Waterproofing for conversions, underpinning and new basements.
Retaining Wall & Foundation Waterproofing
External coatings, membranes and drainage.
Spray-Applied Basement Waterproofing
Machine-applied tanking without weak spots.
Vault Waterproofing
Making pavement vaults dry and usable.
Cellar Waterproofing
Dry cellars finished with plywood walls.
Sump Pump Systems & Services
Twin pumps, battery back-up and servicing.
Basement Floor & XPS Insulation
Dry, warm floors beneath the membrane.
Structural Cracks Repair
Stitching cracks using helical bars.
Can a crack outside let penetrating damp in?
Yes. External wall cracks are a common route for penetrating damp. A narrow opening in render, brickwork or a mortar joint can draw rain into the wall by capillary action.
Why cracks on the outside matter
- The sponge effect: older bricks and traditional render readily absorb water. A crack lets it pass beyond the wall's outer protection into the layers beneath.
- Freeze-thaw damage: moisture entering a crack in autumn can freeze and expand in winter, damaging the wall internally and making the opening wider.
- Driving rain: wind pushes rain against the facade, forcing water into even narrow cracks.
What happens inside? Moisture travels through a wall soaked by rain. Inside, this may leave wet patches, peeling paint, blown plaster and black mould that is harmful to health.
Crack repair: inspect inside and stitch the masonry
An internal coat of paint will not stop water entering. We assess the wall from inside as well as repairing the external crack:
- Inspection from the inside (essential): we measure moisture, use thermal imaging to locate hidden damp, establish how far it has spread and examine the plaster, timber and any mould.
- Assessing the crack: we check whether it runs vertically, horizontally or in steps along mortar joints, how wide it is and whether it continues to move. Stepped or widening cracks may indicate settlement and call for a structural assessment.
- Crack stitching with helical bars (Helibar): for a lasting repair, we cut across the crack into mortar joints and bond stainless steel helical bars into the slots with specialist grout. This ties the masonry together to prevent the crack reopening. Find out about structural crack repair.
- Filling and repointing: we clear the crack, use weather-resistant repair mortar to fill it and repoint surrounding joints where necessary.
- Water-repellent treatment: a breathable treatment then protects the repaired facade against rain while allowing moisture to escape.
Above ground
Damp on upper walls and its effects
Penetrating damp is not confined to basements. Weather and defects on a building's exterior are the usual causes higher up; left unresolved, the moisture can encourage mould and fungi.
What causes penetrating damp high on a wall?
On upper floors, the cause is commonly weather exposure combined with an external defect:
- Damaged roofs and gutters: leaks in roof coverings, defective valleys and blocked or cracked gutters can send water down walls or beneath the roof covering.
- Strong winds and driving rain: exposed upper walls face wind-driven water, which can enter through fine render cracks, worn joints or facade gaps.
- Leaks around windows: deteriorated sealant or seals, or poorly installed upper-floor windows, can allow water to soak into the wall.
Black mould and fungi that damage timber
When penetrating damp is left untreated, black mould and other household fungi can develop:
- Dry rot (Serpula lacrymans): fleshy, large fruiting bodies and strands that transport the water needed for growth.
- Cellar fungus (Coniophora puteana): wet rot affecting floor and ceiling timbers, identified by slender dark brown or black strands.
- Mine fungus (Antrodia sinuosa): cream or white growth that reduces timber to powder.
- Black mould (Stachybotrys chartarum): dark green growth following prolonged wetting of wallpaper or plasterboard; it produces harmful mycotoxins.
- Aspergillus: black or yellow-green patches with strongly allergenic spores that can cause respiratory aspergillosis.
- Penicillium: blue or greenish growth that can spread quickly over damp paint and plaster.
A two-stage approach
How we treat penetrating damp
The source of the water must be removed to resolve penetrating damp. We stop it entering from outside first; only after the leak is fixed do we dry and restore the interior.
When must damp plaster be removed?
The answer depends on the plaster and the extent of the damage. If the leak was stopped promptly, the wall was wet only briefly and the plaster remains firmly attached without flaking, deep mould or salt deposits, it can usually stay. We dry the wall, treat surface mould if present, then make good and redecorate once it is dry.
Signs that plaster needs removing
- It is flaking, sweating or falling off: moisture has weakened the material, so fresh paint or filler will not hold.
- It sounds hollow: a hollow note when tapped indicates that the plaster has detached from the masonry.
- Mould has grown deep into it: weeks or months of moisture can let spores penetrate the plaster, beyond the reach of surface cleaning.
- Salt deposits have appeared: salts carried from the building materials can crystallise within and on the plaster, causing it to break down.
- It is gypsum plaster: gypsum readily takes up water, softens and supports mould, so removal is more often necessary than with cement-lime plaster.
Tapping helps establish whether plaster remains sound: a firm, clear note contrasts with the dull, hollow sound of detached plaster. If removal is needed, we extend it by around 50 cm beyond the visible patch, as moisture may have travelled further within the wall.
From start to finish
Help with the whole repair
One team handles the penetrating damp work from the initial visit through to the finished wall. We trace the water, repair the exterior and restore the affected rooms, coordinating the work inside and out.

Advice on prevention: we explain what to monitor after the repairs. Checking external render and the wider facade, flashings, gutters and seals around doors and windows can reveal the places where leaks commonly begin. Promptly repairing minor cracks and keeping rainwater drainage clear helps reduce the chance of penetrating damp returning.
Our materials
Established manufacturers and compatible materials
We select proven products from manufacturers including Newton, Wykamol, Delta, Biokil and Mapei. We are approved installers for Wykamol, Delta and Biokil, and use a complete, compatible system for every waterproofing installation.
NEWTON
Newton
Membranes for cavity drainage and associated pump systems.

Wykamol
Tanking slurries, membranes and sump pumps.

Delta
Drainage channels, studded membranes and pumps.

Biokil
Products for damp proofing and mould treatment.
Mapei
Waterproof coatings and mortars for repairs.
Common questions
Penetrating damp FAQs
How is penetrating damp different from rising damp?
Rising damp moves upwards from the ground through pores in masonry, so it remains low on the wall. Penetrating damp enters from outside or a leaking pipe. It may appear anywhere between basement and top floor and often worsens following heavy rain.
How will you locate the source of penetrating damp?
We examine the affected rooms and the building exterior, take moisture readings and use thermal imaging to identify damp that is hidden from view. This helps us find the water's entry point rather than address only the visible stain.
Can new paint or plaster solve the problem?
No. Moisture, salts and mould can reappear through a new finish while water is still entering. We repair its source and dry the wall before painting or replastering.
Should my basement have Type A tanking or a Type C membrane?
Either system can work in many basements. Where structural cracks are numerous, walls move or traffic causes vibration, we use Type C. Because its membrane is separate from the wall, a new crack behind it need not make the room wet.
Could a small crack outside cause damp inside?
Yes. Capillary action draws water into fine gaps in brick, render or mortar, while driving rain pushes it further in. We examine the interior and repair the outside crack, often by stitching it with helical bars.
Will you need to remove all the plaster?
Not necessarily. Firmly bonded plaster exposed to moisture only briefly can often be dried and redecorated. Hollow or flaking plaster, gypsum plaster, or plaster containing salts or deep mould usually needs removing, extending around 50 cm beyond the patch.
Who is responsible for penetrating damp in a rented home?
In the UK, responsibility generally rests with the landlord or the freeholder or managing agent collecting the service charge. Tell them about the damp in writing. Our survey report can help identify where water enters.
How can I book a penetrating damp survey in Richmond?
Arrange a survey online, or call our specialists on 020 8432 3350 or 07720 752231. Consultation is free; surveys beyond 10 miles from our base carry a charge in line with our price list.
Free consultation
Arrange a penetrating damp survey in Richmond
Concerned about penetrating damp or any of the fungi described above? Get in touch for a free consultation or a survey. Surveys more than 10 miles from our base are charged in accordance with our price list. Speak to our specialists on 020 8432 3350 or 07720 752231.
07720 752231
Describe the damp problem
Please complete the fields marked *. We will contact you to arrange a survey once we receive your details.
The local setting
What we inspect around Richmond
Around Richmond, properties include brick houses, conversions and homes with basements or cellars. From streets near Richmond Green to the riverside, each building needs its own assessment: we do not assume the source of a damp wall from its setting alone.
We inspect roof coverings, gutters and downpipes, then examine pointing, render, cracks and window seals. Inside, we consider service pipes; below ground, we check walls, floors and joints. The findings guide our recommendation, whether that is an exterior repair, crack stitching, basement waterproofing or combined work.

Keep water out at the source
Our 5-star Google rating means a great deal to us. Read the reviews, arrange a survey or speak with a specialist on 020 8432 3350.
Qualified Specialists & a 10-Year Guarantee
Our family-run team holds CSSW qualifications, with a minimum of 10 years’ experience each. We back our work in Richmond with a 10-year guarantee covering workmanship, plus a QANW Insurance Backed Guarantee that transfers to the new owner if you sell your property. Based in Croydon, we work on domestic and commercial properties across London and the South East.
See What Our Clients Say
We are proud of our 5-star Google rating. Book a survey in our Booking Survey section, or call our specialists on 020 8432 3350 or 07720 752231.
Where we work
Penetrating damp services near Richmond
Crystal Damp Proofing & Basements Ltd investigates and treats penetrating damp in Richmond and surrounding areas, including Twickenham, Kingston upon Thames and Hounslow. Select an area below for its local page.












